[. . . ] 7 Setting Impression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Setting Margins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Shift and Shift Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Caps Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 1) Pull down the rear compartment door and connect the power cord to a proper AC outlet. When the typewriter is switched on, the green LED on the keyboard will light up. The carrier will move to the extreme left of the typewriter then advance to the left margin. The unit is now ready for typing. 5 NOTE: The Socket-outlet shall be installed near the equipment and shall be easily accessible. Setting When you open the printcover to change the RIBBON, DAISYWHEEL, CORRECTION TAPE or other reasons, and if you want to re-initialize your typewriter, press the CODE + = (SETTING) key. 1) Open the printcover and change the RIBBON, DAISYWHEEL or CORRECTION TAPE. 2) Press the CODE + = (SETTING) key, the typewriter will then initialize itself. All memories and carrier position will be maintained. 5 -4- CHANGING Changing The Ribbon Cassette 1) Move the print carrier to the center of the platen using the SPACE or BS key. 2) Hold the ribbon cassette on both sides and lift up the front portion (where the ribbon is exposed) to remove the cassette. 3) To insert a new cassette, place the back end of the cassette on the cassette holder on the carrier and gently press down on the front of the cassette unit it clicks into place. 4) Turn the ribbon feed knob counter-clockwise again to take up any slack in the ribbon. 5) Presss the CODE + = (SETTING) key. Changing The Print Wheel 1) Move the print carrier to the center of the platen using the SPACE or BS key. 3) Place the daisy wheel into the slot with the characters facing the platen. 5) Press the CODE + = (SETTING) key. -56 Changing The Correction Tape 1) Move the print carrier to the center of the platen using the SPACE or BS key. 2) To replace the correction tape, lift out the typing ribbon cassette (see Changing The Ribbon Cassette) and remove the two spools of the lift off tape by pulling them outwards. 3) Place the empty spool of new tape on the left pin so that the tape winds clockwise. Pull the tape around the right guide and place the loaded spool on the right pin so that the tape unwinds counter-clockwise. 4) Manually turn the left-hand spool in the clockwise direction, tightening the tape until resistance is felt. 6) Press the CODE + = (SETTING) key. 7 -6- BASIC FEATURES Selecting Pitch There are three pitches available for typing: PICA (10) : 10 characters per inch CODE + 6 ELITE (12) : 12 characters per inch CODE + 7 MICRO (15) : 15 characters per inch CODE + 8 Selecting Line Spacing There are three line spacing settings available when the appropriate key is depressed. Single line spacing CODE + 3 1 1/2 line spacing CODE + 4 Double line spacing CODE + 5 Setting Impression You can choose one of two hammer impression levels - low, high. The low key is selected initially. Setting Margins You may freely adjust the margins. · Left Margin Move the carrier to the desired position and press the MAR L key. · Right Margin Move the carrier to the desired position and press the CODE + MAR R key. [. . . ] Corrections cannot be made MAINTENANCE We recommend that your typewriter be adjusted, serviced, and lubricated by a qualified service technician at least once a year. If you need help, contact your local dealer for checking your machine. *NOTE: For best performances, try to use only standard supplies from your dealer. The use of non-standard supplies including Ribbons, Correction Tapes and Print Wheels, may cause poor performance or damage to your typewriter. [. . . ]